Sparks, a dead circuit or a buzzing panel in Alice? Lines are answered 24/7: one free call connects you with a local pro, typically within 30–60 minutes. Backed by 20+ Years Of Experience.
Free Call · Answered 24/7 · Local Pros Near You
Rated Excellent By Homeowners
Across The USA
If you smell burning, see sparks, or lose power in part of your Alice home, treat it as urgent: call now. One free call connects you with a local pro who can arrive in 30–60 minutes, at any hour. A pro can isolate the fault and make the panel safe.
Type your ZIP code to check it against the areas Alice covers.
The six services cover the problems Alice homeowners call about most: a breaker that will not stay on, a panel worn by fifty summers of heat. Each card explains when it is needed. All six are one call away, day or night, for any Alice household.
Dead outlets, damaged circuits and faulty wiring in Alice homes are traced to the failure point, then repaired so the circuit is safe to use again. A local pro can check the older wiring runs common in pre-1980 homes before power is restored to the circuit.
Call Now — FreeInstant tripping, a warm face, or a breaker that refuses to reset points to a worn breaker or a fault further down the circuit in an Alice home. A local pro can prove whether the breaker or the circuit is at fault, fit the replacement, and leave the panel safe.
Call Now — FreeWhen a Gulf storm knocks power out across Alice, a generator that will not start or a transfer switch that will not switch leaves a home exposed to heat within hours. A local pro can diagnose starting, switching and fuel-side electrical faults, restoring backup power where safe.
Call Now — FreeMany Alice homes still run on panels fitted around the median build year of 1974. When a panel shows heat damage, corrosion or repeated breaker failures, a local pro can fit modern equipment sized for today's loads and arrange the inspection.
Call Now — FreeFlickering lights, a circuit that dies only under load, or voltage that swings across an Alice home needs proper fault-finding, not guesswork. A local pro can test each circuit in turn, pin down where the fault sits, and show you the readings that prove it.
Call Now — FreeOverhead lines around Alice leave homes exposed when lightning or utility switching sends a spike through the service. A surge protective device fitted at the panel by a local pro can clamp that spike before it reaches cooling equipment or appliances.
Call Now — FreeAlice is a compact city, and our research found no officially listed named neighborhoods here, so this page does not invent any. Service covers the whole 78332 and 78333 area: the older streets near the centre, the homes along the highways out of town, and the rural addresses beyond them. Every address in those ZIP codes is covered the same way — one free call, any hour.
Alice is a community in Jim Wells County with no officially listed neighbourhood districts in our research — and we will not invent any. Service covers the whole 78332, 78333 area: the homes along its roads, houses, mobile homes and outbuildings across the surrounding area.
If you are near Alice rather than in it, check the nearby cities below — a pro may still be close to you.
An electrical problem in Alice rarely fixes itself, and in a pre-1980 home it can worsen within hours as heat builds at a failing joint and insulation starts to scorch. One free call connects you with a local pro at any hour, typically within 30–60 minutes, so the fault is found tonight rather than after it has spread quietly through the walls.
Step 1. Switch off the affected breaker if safe before you call us.
Step 2. Unplug appliances on the sparking circuit before you call us.
Step 3. Keep children and pets away from the panel
Calls Answered 24/7 · Free To Call · No Obligation
Call any time, day or night. The call is free, a real person answers, and you explain what is happening at your home.
Your call is connected to an independent local professional who covers your area and handles the problem you described.
The pro calls you back or visits to check the problem in person, explains what they find, and agrees the next step with you.
Alice is covered by two ZIP codes, 78332 and 78333, spanning the city and its rural edges. Enter your ZIP to confirm your address, or call: one free call connects you with a local pro day or night.
Nearby areas are often covered too — one free call checks your exact address in under a minute.
Real reviews from people who called for emergency help.
Travis Calhoun
Houston, Texas
An electrical burning smell filled our hallway after our central AC tried kicking on. The technician traced the issue to a scorched wire junction inside a hidden junction box in the attic. He made clean, code-compliant repairs in no time.
Samantha Wu
Dallas, Texas
A heavy freeze followed by high winds caused our overhead service drop line to pull away from the roof weatherhead. The emergency electrician secured the mast, repaired the weatherhead, and coordinated directly with Oncor for rapid reconnection.
Darrell Jenkins
Austin, Texas
Woke up to flickering lights and a drop in voltage across half the house. He identified an open neutral coming from the main feed, preventing sensitive electronics from frying. Fast, polite, and deeply knowledgeable.
Cynthia Sterling
Fort Worth, Texas
Our tenant called in panic when sparks shot out from behind the refrigerator receptacle. The technician arrived in under an hour, replaced the melted outlet, and inspected the whole branch circuit for heat damage.
Thomas Albright
San Antonio, Texas
Our automated main transfer switch for our whole-home generator failed during a severe power outage. The electrician showed up promptly at 2 AM, diagnosed the bad solenoid, and manually bridged our backup power safely.
Natalie Mercer
El Paso, Texas
Desert wind storms knocked out power to our medical equipment room at home. The dispatcher prioritized our call, and the technician fixed a blown service fuse within 40 minutes of our call. Lifesaving service.
Victor Sandoval
Arlington, Texas
A power surge fried our pool pump subpanel and left hot wires exposed. The electrician capped everything safely, installed a surge mitigation module, and verified grounding rods were intact.
Patricia Zimmerman
Plano, Texas
Electrical smoke was coming out of our hallway recessed lights. The electrician crawled through a hot attic, identified a rodent-chewed Romex line, spliced it inside an approved junction box, and restored safety.
Dustin Foley
Corpus Christi, Texas
Our commercial refrigeration line suffered an unexpected voltage drop that risked thousands in perishables. The emergency technician arrived within an hour, repaired the fused disconnect, and got the coolers humming.
Melanie Sutton
Lubbock, Texas
Our heavy machinery workshop lost three-phase power during a crucial production cycle. Their emergency commercial team diagnosed an open delta transformer feed fault and coordinated the fix rapidly.
Russell Newton
Irving, Texas
Our main breaker handle snapped completely off while we were trying to shut down power during a water leak. He safely executed a live-side isolation and replaced the complete breaker mechanism within 90 minutes.
Joyce Moran
Laredo, Texas
When high summer heat caused our air conditioner feed wires to melt inside the disconnect, this electrician arrived within the hour with replacement gauge wire and got our cooling restored.
Wayne Little
Garland, Texas
Fast and honest emergency electricians. They fixed an arcing 240V clothes dryer receptacle that scorched our sheetrock, replacing the receptacle and testing the breaker for safety compliance.
Beverly Houston
McKinney, Texas
Punctual, professional, and transparent about emergency call-out pricing. They fixed a chewed wiring harness in our attic that took out all upstairs lights right before a holiday event.
Eugene Lambert
Amarillo, Texas
Heavy winter winds ripped the service drop clevis right off our exterior wall. The electrician re-anchored the mast securely, replaced the torn weatherhead, and coordinated rapid utility re-energizing.
Loretta Manning
Brownsville, Texas
Prompt and respectful electrician who fixed an arcing breaker that fed our refrigerator and nursery. Clear explanations, fair emergency rates, and total peace of mind.
Marcus Vance
Los Angeles, California
Our main 200-amp breaker started buzzing loudly and sparking at 11 PM on a Friday. Their emergency electrician arrived within 45 minutes, replaced the arcing breaker safely, and balanced the load panel. Exceptional speed and true lifesavers.
Elena Rostova
Miami, Florida
During a severe tropical thunderstorm, lightning struck nearby and fried our exterior meter base and whole-home surge protector. The technician worked in the rain with proper safety gear, restored power safely, and documented everything for our insurance claim.
Brenda Castillo
San Diego, California
Half of our home lost power after an overloaded breaker tripped and refused to reset. The electrician diagnosed a degraded neutral bus bar, replaced the burnt hardware, and ensured all circuits tested safely before leaving.
Garrett Lindholm
Orlando, Florida
Water from a roof leak entered our main service panel in the garage, causing loud pops and smoke. The emergency team arrived fast, safely killed power at the meter, dried and rewired the damaged panel circuits, and verified no shorts remained.
Derrick Holbrook
San Jose, California
Our commercial kitchen exhaust fans shorted out right before the dinner rush. Their on-call commercial electrician diagnosed a melted magnetic contactor, replaced it from his truck inventory, and saved our entire evening of reservations.
Clara Higgins
Tampa, Florida
The ground-fault circuit interrupters across our bathrooms and kitchen kept tripping simultaneously. The technician methodically isolated the circuit, found a damaged underground feed line, and completed a safe bypass.
Alicia Warren
San Francisco, California
Old Victorian wiring can be a nightmare during an emergency. When our plaster wall outlets started smoking, the electrician navigated the legacy knob-and-tube junction safely and isolated the threat without destroying our walls.
Richard Henderson
Jacksonville, Florida
A tree branch fell on our power mast, bending the riser and pulling wires loose. Their emergency technician rebuilt the mast to current Florida building code standards, and power was restored the very same day.
Kenneth O'Connor
Sacramento, California
During a summer heatwave, our main disconnect switch overheated and shut down our entire house. The on-call master electrician replaced the switchgear safely, wore full PPE, and kept us informed through each step.
Latoya Robinson
St. Petersburg, Florida
A corroded subpanel in our detached garage started arcing violently. The technician replaced the corroded breakers, cleaned the bus bars, and sealed the enclosure against coastal moisture. Exceptional service.
Hannah Phillips
Fresno, California
Severe buzzing inside our interior breaker box turned out to be an arcing double-pole breaker on the water heater circuit. The tech swapped the breaker and torqued all panel lugs to factory specifications.
Clifford Hayes
Fort Lauderdale, Florida
Salt air intrusion caused severe pitting on our main service disconnect lugs. They performed an emergency replacement, used dielectric compound on all connections, and resolved our persistent power dips.
Bradley Cooper Jr.
Oakland, California
Had an emergency where our exterior meter loop caught fire after an insulation failure. The crew worked cleanly, liaised with PG&E directly, and re-wired the drop without any administrative delays.
Denise Griffin
Cape Coral, Florida
Hurricane winds tore our conduit away from the exterior wall. Their emergency team installed heavy-duty exterior strapping, replaced the sheared wire, and passed the subsequent city inspection effortlessly.
Courtney Bishop
Long Beach, California
Our whole lower floor lost power suddenly on a holiday weekend. The emergency tech identified a loose neutral wire inside the meter pan and secured it quickly. Very reasonable emergency diagnostic rates.
Gary Strickland
Tallahassee, Florida
Lightning caused a violent spike that destroyed three dedicated circuits and our well pump controller. The electrician arrived promptly, rebuilt the control circuits, and ensured our water was running again.
Leonard Pratt
Bakersfield, California
Our main AC circuit breaker kept tripping instantly with a loud bang. He tested the circuit with an insulation resistance tester, pinpointed an exterior ground fault, and re-pulled the wire neatly.
Angela Higgins
Pembroke Pines, Florida
Water from our upstairs AC overflow pipe dripped directly into the main electric panel. The technician isolated the box, sanitized and dried the breakers, and replaced two corroded circuits right away.
Rebecca Dalton
Anaheim, California
A burning plastic smell in our master bedroom led us to an overheated dimmer switch that was hot to the touch. The electrician replaced it with an industrial-grade switch and thoroughly inspected the load capacity.
Arthur Chapman
Hollywood, Florida
Flash flooding near our patio threatened an outdoor hot tub subpanel that started throwing sparks. The emergency electrician locked out the circuit, secured the conduits, and made the backyard completely safe.
Craig Underwood
Riverside, California
Clear quotes and honest diagnostic fees. When our subpanel caught fire in the workshop, they safely replaced the entire panel enclosure, re-labeled all breakers, and left the workspace clean.
Gloria Barnett
Gainesville, Florida
As a senior living alone, having my power shut off with a loud buzzing from the panel was terrifying. The technician arrived with extreme kindness, calmed my anxiety, and repaired a broken main breaker quickly.
Valerie Dawson
Santa Ana, California
Top-notch emergency response when our solar inverter began smoking and threw our residential panel into a fault state. The electrician disconnected the solar link safely and restored standard utility grid flow.
Timothy Floyd
Miramar, Florida
A severe thunderstorm created a floating ground situation in our home, causing metal appliances to tingle. The emergency technician drove out late at night, drove new ground rods, and bonded the plumbing correctly.
Phillip Vance
Stockton, California
Very satisfied with their midnight response. Our commercial parking lot lights suffered a severe underground short that tripped our main facility breaker. The technician isolated the exterior short and restored interior operations.
Stephanie Collier
Coral Springs, Florida
Lightning struck our pool pump timer box, blowing the door wide open. The technician arrived the same morning, replaced the scorched components, and checked all surrounding grounding paths.
Teresa Byrd
Irvine, California
Our EV charger shorted out our garage subpanel late in the evening. The electrician arrived swiftly, installed a heavy-duty industrial breaker, and confirmed wire gauge suitability to prevent future overloads.
Lawrence Frost
Clearwater, Florida
Dependable emergency service. When an older Zinsco panel in our rental property began arcing and smoking, they arrived immediately, stabilized the panel, and scheduled a safe modernization.
Keith Ramsey
Chula Vista, California
Outstanding emergency troubleshooting. He located a high-resistance fault inside our wall that had been causing lights to flicker and breakers to overheat for weeks. Superb precision.
Brooke Faulkner
Palm Bay, Florida
Our well pump pressure switch caught fire following a surge. Their on-call technician showed up with the exact pressure switch in his van, rewired it neatly, and restored running water to our home.
Amber Giles
Fremont, California
Woke up to sparking sounds coming from our hallway return vent where an unshielded wire had chafed. The electrician arrived promptly, cut power, and enclosed the junction safely in metal conduit.
Douglas Skinner
Pompano Beach, Florida
Coastal storm surge threatened our dock power pedestals and shorted the main breaker. The technician arrived fast, isolated the waterfront loop safely, and restored interior electricity without delay.
Franklin Tate
San Bernardino, California
A severe branch snap crushed our overhead electric mast. Their emergency team installed a new heavy-duty service mast, pulled new conductors, and handled the municipal emergency permit seamlessly.
Carolyn Santana
Lakeland, Florida
If you experience an electrical emergency anywhere in Central Florida, call this crew. They responded to our smoking breaker panel within 35 minutes on a Sunday night and resolved the dangerous short safely.
Electrical help is also covered in the listed communities around Alice, across Jim Wells County and the surrounding South Texas counties, and each place below has its own page with its own local housing picture, its own data, and the same around-the-clock cover.
70.4% of homes here were built before 1980, so older panels and wiring are common.
57.5% of homes here were built before 1980, so older panels and wiring are common.
61.8% of homes here were built before 1980, so older panels and wiring are common.
40.9% of homes here were built before 1980, so older panels and wiring are common.
52.0% of homes here were built before 1980, so older panels and wiring are common.
33.5% of homes here were built before 1980, so older panels and wiring are common.
Still not sure what is happening at your home? Call and describe it. A real person answers, day or night, and the call is free.
One free call connects you with a local pro near Alice who can typically arrive in 30–60 minutes — day or night.
Call (800) 555-0100Free call · Open now · 24 hours a day, 7 days a week
Alice's electrical risks start with the age of its housing. This Jim Wells County city of 17,707 people and 7,016 housing units (US Census Bureau, ACS 2024) carries one of the oldest housing stocks in the region, and its wiring feels every South Texas summer.
A full 63.8% of Alice homes were built before 1980, and the median home dates to 1974. Panels, breakers and branch wiring from that era were sized for smaller loads than today's air conditioning, dryers and kitchen appliances draw, and connections loosen through decades of heat cycles. Only 3.8% of homes date to 1939 or earlier, so the very oldest wiring methods are uncommon — the risk sits in the post-war decades instead.
South Texas heat holds cooling circuits near their limits for hours a day, month after month. That sustained load exposes tired breakers and slightly loose lugs faster than any other stress, and attic cable runs bake at temperatures that age insulation early. Garages and sun-facing walls make it worse, because panels mounted there bake all afternoon.
Thunderstorms and tropical weather bring lightning surges, wind-thrown branches and driving rain to overhead services across Alice. Water finding its way into an outdoor disconnect or panel corrodes contacts quietly, and a mast bent by storm winds leaves the service entrance damaged even when the lights come back on. Owner-occupiers make up 57.5% of households here, so most repairs are arranged directly by the people who live with the risk.
Free call · Answered 24/7
The figures below come from the Census Bureau's ACS 2024 release for Alice, and they explain why older panels and ageing wiring drive so many urgent calls here across the city every single week.
17,707
Population
ACS 2024
7,016
Housing Units
ACS 2024
63.8%
Homes Built Before 1980
ACS 2024
4.0%
Mobile Homes
ACS 2024
57.5%
Owner-Occupied Homes
ACS 2024
Jim Wells
County
US Census Bureau
Ageing panels and original wiring set the pattern, because 63.8% of Alice homes were built before 1980 (US Census Bureau, ACS 2024). Most urgent calls involve a breaker that trips and will not reset, lights that flicker when the air conditioning starts, a buzzing panel, or a dead circuit in one part of the house.
The causes repeat. A loose connection at a breaker or outlet builds resistance and heat. An overloaded circuit strains when cooling, kitchen appliances and a water heater share wiring sized for a smaller household. Wire insulation that has baked through decades of South Texas summers turns brittle and cracks, exposing conductors inside walls.
Many panels here were fitted when the median home was built in 1974, long before central air, large dryers and EV charging became normal household loads. The bus bar and breakers in those panels have cycled under load for fifty summers.
Contact points pit and loosen with age, and a poor contact arcs in tiny bursts. Each cycle is a chance for an arc fault to start at a contact that no longer grips. The signs are warm breaker faces, a faint burning smell at the panel door, and lights that dip when a large appliance starts. A thermal imaging scan can show a hot lug or breaker without anyone touching live parts, and torqueing panel connections back to specification sometimes settles a panel that looked finished.
Fault-finding is a sequence: make the circuit safe, then test one circuit at a time under load. Circuit tracing and fault finding means checking voltage at the panel, then at devices along the run, until the failing point shows itself.
Voltage checks confirm an open neutral or a lost leg of service in minutes, which separates a utility-side problem from one inside the home. Readings at the main breaker show whether a fault sits before or after the panel. Heavy appliances belong on a dedicated circuit of their own, because sharing is what pushes older wiring past its rating. Repairs are checked against the National Electrical Code (NEC / NFPA 70), and panel work in Texas sits under rules overseen by TDLR, the state licensing board. If you are comparing help across the region, the page for an emergency electrician in Texas explains how the statewide service works, and the guide for an emergency electrician in Agua Dulce covers the smaller community up the road.
Heat is a stress test that runs for months, holding air-conditioning circuits near their rating for hours every day. Copper wiring tolerates the heat when connections stay tight; trouble starts where connections have loosened or where aluminium branch wiring from the 1960s and 1970s meets devices not rated for it.
Attics make it worse. Cable runs through a superheated attic age faster, and a junction box buried under insulation can hide a failing splice for years. A whole-home surge protector at the panel guards against the spikes that ride in when summer thunderstorms sweep across Jim Wells County.
Storm damage above the meter follows a set sequence. The service mast, weatherhead and meter base belong to the property side, so a pro repairs or replaces them; the overhead service drop and the meter belong to the electric utility.
Once the property-side equipment is rebuilt and inspected, the utility reconnects and reseals the meter. Our guide to Utility Reconnection After Meter Or Mast Damage: The Steps In Order walks through that sequence in full, and the page on How To Document Electrical Damage For An Insurance Claim shows what to photograph and record before anything is moved. Neighbouring communities follow the same steps — see the page for an emergency electrician in Bishop.
The parts needed, the time on site, and how much damage the fault has already done decide the cost — a failed breaker is quick, while a burnt bus bar or a damaged meter base takes longer and needs more parts.
The hour matters too: nights, weekends and holidays are priced differently from weekday hours, and a fault hidden inside a wall takes longer to trace than one sitting visibly at the panel.
Reviewed By Hamza
Master Electrician & Emergency Power Restoration Specialist
Hamza is a master electrician and emergency power restoration specialist with extensive field experience resolving critical residential and commercial electrical hazards across California, Florida, and Texas. He specializes in thermal arc-fault diagnostics, emergency panel replacements, storm-damaged service mast repairs, and whole-home surge mitigation to protect properties from electrical fires and extended outages.
Updated October 30, 2026
Alice's housing is markedly older than Texas as a whole: 63.8% of homes here were built before 1980, against 33.2% statewide, and the median Alice home dates to 1974 while the Texas median is 1992. The bars below rank Alice against other Texas communities.
Compared with the other cities in Texas we serve, using US Census Bureau ACS 2024 5-year estimates.
Tap the signs you are seeing and the checker will say what they point to and whether to call now. It covers five signs: burning smells, panel noises, breakers that will not reset, flickering lights, and hot outlets. Only a pro can confirm the problem.
